Last verified against the primary source on Sep 12, 2026.
Used Haas Mini Mill: $14,950–$29,950 observed used across 10 listings. The documented cost risk to price in: X-axis cable. Buy only after inspection.
Confidence 45%10 observed comparables
As of Aug 19, 2026What can make the cheap machine expensive?
| Component | Severity | Documented repair cost |
|---|---|---|
| Slow tool release | medium | not yet verified |
Common Mini Mill wear cluster: the Humphrey solenoid valve gets sticky and slows tool release; the Z-axis limit proximity-switch screws back out so travel over-runs; and a loud clunk on Z-home. Owner: "Having learned the humphrey valve can become sticky over time and cause this. I had two spare of this $5.85 part on hand," and "the Z axis limit proximity switch screws are nearly fallen out and the sensor is out of position." Cheap parts, but easy to misdiagnose.
Cost not yet verifiedHaving learned the humphrey valve can become sticky over time and cause this. I had two spare of this $5.85 part on hand
Common questions
How much does a used Haas Mini Mill cost?
Observed listings range roughly $14,950 to $29,950 depending on age, condition, and configuration (as of 2026-08-19).
What fails on the Haas Mini Mill?
The most cited concerns in our evidence record: Slow tool release. See the risk breakdown above for details and sources.
Live listings on eBay
Live listings via the eBay Browse API. Links are affiliate-tracked and CNC Ledger may earn a commission on qualifying purchases, at no cost to you.
From the research record
- PRICE: - Machinio Mini
- FAILURES: - Tool-release air-line failure via a clogging Humphrey valve — a Mini-Mill-specific pneumatic failure mode, per a video titled explicitly for the TM-1 Mini-Mill: video transcript: https://www.youtube.com/watch?v=Crbh9wzVVAw (title: "HAAS Fix Tool Release Issues due to defective Humphrey valve clogging the air lines — TM-1 Mini-Mill") Note: this ev
- REPAIR: - General cross-platform spindle rebuild-vs-replace economics exist (Haas VF-series line item: rebuild $4,800–$7,200, replacement $16,000–$24,000): https://midwestcncservices.com/insights/spindle-diagnostics/rebuild-vs-replace-spindle-economics/ CAVEAT: this source is explicitly VF-series-focused (larger direct-drive spindle cartridges). The Mini M
- VIDEO (00:00:03 https://www.youtube.com/watch?v=cwYsbzAW3r0): "[Music] all too often a spindle is replaced"
- VIDEO (00:00:06 https://www.youtube.com/watch?v=cwYsbzAW3r0): "all too often a spindle is replaced"
- VIDEO (00:00:06 https://www.youtube.com/watch?v=cwYsbzAW3r0): "all too often a spindle is replaced without getting to the root cause of the"
Sources
- machinestation.usweb · research-cited · accessed 2026-08-19
- youtube.comweb · research-cited · accessed 2026-08-19
- youtube.comweb · research-cited · accessed 2026-08-19
- midwestcncservices.comweb · research-cited · accessed 2026-08-19
- r.jina.aiweb · research-cited · accessed 2026-08-19
- machinio.comweb · research-cited · accessed 2026-08-19
- Spindle Troubleshooting - Haas Automation Servicevideo-transcript · research-cited · accessed 2026-08-19
- Haas minimill 2 with clogged grease linesvideo-transcript · research-cited · accessed 2026-08-19
- Mini Mill loud clunk homing Z / slow tool release (Practical Machinist)forum · verified-primary · accessed 2026-09-12
Spot an error? Challenge this record
Found an out-of-date code section, a wrong verdict, or a better primary source? Tell us. Corrections that check out are applied, with the change shown in history. That is our standing policy.