# Haas ST-10 vs ST-20: What Haas Publishes and How to Inspect Either

> Compare the Haas ST-10 and ST-20 on published chuck, bar, spindle, travel and weight figures, plus what Haas says about turrets, chucks and warranty transfer.

Updated: 2026-10-27. Source: CNC Ledger — https://cncledger.com/guides/haas-st-10-vs-st-20/ (claims cited to primary sources; see /methodology/).

The Haas ST-10 and ST-20 are two sizes in the same ST Series lathe family. Earlier versions of this guide described turret crashes, bearing failures and bed twist drawn from repair anecdotes and listed dealer prices. We removed those claims because no official source states them. What follows is what Haas publishes, plus what to check on any used lathe.

## The published differences

Haas describes the smaller machine this way.

> The ST-10 has an extra-small footprint, yet provides a generous work envelope.

The ST-10 page lists 1.75" bar capacity, 15 HP, 6k RPM and a 6.5" chuck. The ST-20 pre-installation guide lists 2.5" bar capacity, a max rating of 20, 4k max speed and an 8.3" chuck, with X Axis 8.40 in / 213 mm and Z Axis 22.50 in / 572 mm of travel. Its spindle is rated 20.0 hp (14.9 kW), and the machine weighs 8820 lb (4000.0 kg).

Haas also publishes a family brochure that gives a maximum capacity of 14" x 16" for the ST-10 and 10" x 22.5" for the ST-20. The brochure is older than the current product pages, so confirm the capacity of the exact machine you are looking at against its serial number and options.

## Electrical and turret basics

The ST-20 needs three-phase power: 220 VAC at 40 A, or 440 VAC at 20 A with the optional high-voltage transformer. Both lathes use the family turret that Haas describes in its brochure: ST Series lathes are equipped with a robust, 12-station bolt-on style tool turret. Haas adds that other turrets are available depending on model, so check what is actually fitted.

The Haas lathe manual gives one concrete turret diagnostic that costs nothing to test. Low air supply affects indexing:

> Low air pressure or insufficient volume reduces the pressure applied to the turret clamp/unclamp piston and slows down the turret index time or does not unclamp the turret.

Before blaming the turret, confirm the shop air is adequate and watch several full index cycles.

## Inspect both machines the same way

- Index the turret through every station, forward and reverse, and listen for hesitation.

- Check that chuck jaws do not extend past the chuck face, since the Haas manual warns that jaws must not protrude beyond the diameter of the chuck.

- Run the spindle through its speed range and note any noise or heat.

- Ask for maintenance records, because Haas states that its specified maintenance procedures must be adhered to and recorded to maintain its warranty.

## What the Haas warranty means for a used buyer

The Haas warranty period is one (1) year, so a used lathe may already be outside it. Haas does allow a transfer in a private sale when the warranty is still running. It also excludes wear items such as seals, belts, filters and tool changer fingers. Treat any used ST as sold without Haas coverage unless the seller proves otherwise in writing.

## Sources

Every quotation above was fetched from the document linked here and matched word for word on 2026-10-27.

- [ST-10](https://www.haascnc.com/machines/lathes/st/models/standard/st-10.html) (Haas Automation), checked 2026-10-27
- [ST-10](https://www.haascnc.com/machines/lathes/st/models/standard/st-10.html) (Haas Automation), checked 2026-10-27
- [ST-20 Pre-Installation Guide](https://haascnc.com/pre-install-guide/st-20) (Haas Automation), checked 2026-10-27
- [ST-20 Pre-Installation Guide](https://haascnc.com/pre-install-guide/st-20) (Haas Automation), checked 2026-10-27
- [ST-20 Pre-Installation Guide](https://haascnc.com/pre-install-guide/st-20) (Haas Automation), checked 2026-10-27
- [ST-20 Pre-Installation Guide](https://haascnc.com/pre-install-guide/st-20) (Haas Automation), checked 2026-10-27
- [Lathes: ST Series](https://haascnc.com/content/dam/haascnc/machines/lathes/st-series/assets/Lathes_STSeriesStandard.pdf) (Haas Automation), checked 2026-10-27
- [Lathes: ST Series](https://haascnc.com/content/dam/haascnc/machines/lathes/st-series/assets/Lathes_STSeriesStandard.pdf) (Haas Automation), checked 2026-10-27
- [Lathes: ST Series](https://haascnc.com/content/dam/haascnc/machines/lathes/st-series/assets/Lathes_STSeriesStandard.pdf) (Haas Automation), checked 2026-10-27
- [2023 Lathe Operator’s Manual](https://haascnc.com/content/dam/haascnc/en/service/manual/operator/english_lathe_interactive_manual_print_version_2023.pdf) (Haas Automation), checked 2026-10-27
- [2023 Lathe Operator’s Manual](https://haascnc.com/content/dam/haascnc/en/service/manual/operator/english_lathe_interactive_manual_print_version_2023.pdf) (Haas Automation), checked 2026-10-27
- [2023 Lathe Operator’s Manual](https://haascnc.com/content/dam/haascnc/en/service/manual/operator/english_lathe_interactive_manual_print_version_2023.pdf) (Haas Automation), checked 2026-10-27
- [2023 Lathe Operator’s Manual](https://haascnc.com/content/dam/haascnc/en/service/manual/operator/english_lathe_interactive_manual_print_version_2023.pdf) (Haas Automation), checked 2026-10-27
- [2023 Lathe Operator’s Manual](https://haascnc.com/content/dam/haascnc/en/service/manual/operator/english_lathe_interactive_manual_print_version_2023.pdf) (Haas Automation), checked 2026-10-27
- [2023 Lathe Operator’s Manual](https://haascnc.com/content/dam/haascnc/en/service/manual/operator/english_lathe_interactive_manual_print_version_2023.pdf) (Haas Automation), checked 2026-10-27
- [2023 Lathe Operator’s Manual](https://haascnc.com/content/dam/haascnc/en/service/manual/operator/english_lathe_interactive_manual_print_version_2023.pdf) (Haas Automation), checked 2026-10-27
